Methanation in Synthetic Natural Gas (SNG) Production

Methanation in Synthetic Natural Gas (SNG) ProductionMethanation is the work at of producing methane from H2 and CO. Methane (an odour little and colorless flub, composed of four henry molecules attached to one carbon molecule) is found in natural tout that we nookie employ in our homes for energy. Methane found in natural spoil is produced by anaerobic bacteria, which break down organic material and the waste carrefour is the natural gas. The natural gas that is sought afterwards by companies such as BP drilling for oil and gas was produced by anaerobic bacteria millions of years ago. Methane is employ in many mouldes some of which ar explained below. We will mainly con emplacementr methanation in the production of Substitute Natural Gas (SNG) as this can be used instead of natural gas which has limited resources and supply.Methanation is the reverse response of travel methane reforming. It is one of the most primal steps in ammonia congeals as the COx produced in the overall steam reforming process need to be separated from the H2, as the H2 is to be used for ammonia synthesis. This process is in addition referred to as purification methanation. The content of oxides of carbon in the production of ammonia must be reduced to a very low level to prevent gun poisoning2. After the low temperature shift (LTS) reaction and deduction of carbonic acid gas, the methanation reaction is used to remove any residual COx from the process stream before ammonia synthesis. Trace amounts of CO and CO2 ar reacted with hydrogen in the presence of a nickel oxide catalyst to produce a mixture of methane and water. This process removes the residual 0.2-0.5% CO and 0.1%-0.2% CO2 to about 5ppm (it is brisk to in the production of ammonia to remove the COx as even a low level significantly reduces the methanation rate) by reduction to methane with hydrogen in a fixed- rump reactor, with a 15-35 wt% Ni/Al2O3 catalyst (2).This catalyst is usually prepared by impreg nating high airfoil area - Al2O3 with a soluble Ni salt. MgO can be used to impede sintering of the active Ni crystallites. For this process methanation is normally carried out in an adiabatic, fixed-bed reactor at 30 atm, with an inlet temperature of 300C and an exit temperature of 365C. This reaction is highly exothermic and the temperatures of the bed are kept below 400C so that catalyst sintering and carbon deposition is prevented. 3What is SNG?Substitute/Synthetic Natural Gas (SNG) is confusable to natural gas upright now produced from combust or biomass (e.g. wood, straw, waste). It is a manufactured product which is chemically similar to natural gas. Natural gas is the worldwide fuel of choice but there is limited supply, so SNG is one of the options to overcome this. Producing SNG from biomass is as well considered to be sentiment of as green gas as it avoids extra CO2 emissions, because it is carbon neutral. SNG has many advantages some of which arethe already exist ing gas supply al-Qaida (e.g. pipelines) which allow the gas to be distributed by means ofout a country such as the USA and besides worldwidehigh conversion susceptibility competent final use technologies that are well-established e.g. Compressed Natural Gas (CNG cars), Combined Heat and Power (CHP), and Heating.What is the methanation process and how is it used in the production of SNG?CO + 3H2 CH4 + piddle The reaction between H2 and CO can produce a number of different products depending on the reaction conditions, the catalyst used and the stoichiometry of the reactants. The reaction of great touch to us is the one producing methane. This reaction over a nickel catalyst was first reported by Sabatier and Senderens (1902, 1905) and even though a lot of look for has gone into which catalyst is the best for methanation, nickel has continued as the key catalyst for methanation because of its selectivity for the production of methane, high activity, and inexpensiveness compar ed to other catalysts. Catalysts involved in methanation operate for a long time in catalyst beds and for that reason catalyst life and strength are also of major importance. Many problems such as randomness poisoning are involved with these catalysts they are mentioned in a later section of this report.5The above forward reaction is exothermic, releasing heat (the delta H determine are negative showing this) and the forward reaction is favoured by low temperature and high pressure, Product gas with a high fraction of CH4 can that be generated at low temperature (300-350C) and high pressure 20 bar.6 We also know from Le Chateliers Principle that pressure favours the side with fewer moles which in this oddball is the forward reaction producing methane and water, so a high pressure should be used.The production of methane is a fundamental step in the process of manufacturing that gas from combust to produce SNG. The typical methanation process involved in SNG consists of three f ixed-bed methanating stages that are used in series with a fixed-bed of catalyst. A single stage process can and has also been used for methanation, such as the IRMA Methanation pilot plant KFA mould, the conditions for this single stage were P = 30 bar T = 250-700C (1 stage) volumetric flow rate = 600m3 (STP)h -1, (synthesis gas) 1100 operating hours since 19817. The three stage methanation process consists ofTotal Gasification of the burn in steam, possibly with oxygen, C+H2OH2+ COChanging the dimension of H2 to CO in the product gas by the water gas shift reaction, and then removing any residual CO2. CO+H2OH2+CO2The hydrogen and carbon monoxide are reborn to methane (following the removal of damaging material to the process such as hydrogen sulphide) using a catalyst (nickel is the most reciprocal for this process as explained later in this report.). This final stage is a straight through reactor operating at lower temperature than that of the previous stages as shown in Fi g.1 below. This gives methane which contains typically less than 3% H2, 0.1% CO and has a thermal efficiency of approximately 70% for the total process. This methane produced can then be use in the production of SNG. CO + 3H2 CH4 + H2O 8As the temperature needs to be go outled the product gases are recycled over the first stages with interstage cooling which prevents the temperature from increasing and also means that the process is more than cost-efficient as the gases are recycled and you dont prevail to put extra cooling in to keep the temperature from rising which saves cash. The avoiding of high temperatures also protects the catalysts, if the reaction temperature constructs too high non only is the equilibrium state of the hydrogenation reaction adversely affected but the catalyst life is shortened by sintering of the metal particles9.Fig. 1 shows the three-stage process with fixed-bed reactors and the corresponding thermodynamic equilibrium temperatures for the synthe sis gas with 10% CH4 at stage one and the desired dry product gas with more than 80% CH4. This diagram also shows that after the first stages the temperature decreases again and this is to avoid high temperatures in order to protect the catalyst but also to reach thermodynamic equilibrium at low temperatures. This is done by product gas recycling cooling as explained before.It is also classical to know that when producing SNG by methanation the CO and H2 (i.e. the reactants) will contain a lot more of the monoxide than in the methanation process used for ammonia synthesis. In ammonia synthesis only a small amount of monoxides (less than 1%) are found however in SNG production the methanation process reactants can dedicate 30-50% of the monoxide. It is also important to know that in the purification methanation even a low amount of monoxides can seriously deteriorate the methanation process by catalyst poisoning.8This picture shows the process of coal gasification, and then the pro ducts being cleaned and readied for methanation. Gasification is simply the process of producing coal gas, a mixture of CO and H2 which is known as syngas. This syngas can then be used in the methanation process producing SNG.How methanation is used in industryFrom the 1970s quite a few methanation processes have been developed which consist of fixed bed and fluidised bed methanation. Most of the methanation processes used in industry use fixed bed reactors (used for the methanation in ammonia production, described before) as they are the most common cause of reactor used in industry for many reasons such as having the simplest multi-phase reactor configuration where the solid phase is stationary and complications arising from the second phases mixing modality are not present.10 However, some processes use fluidised bed reactors also as fluidized bed methanation presents the advantage of vertical heat transfer from the process gas side to the cooling medium and the advantage of p articular simplicity when exchanging the catalyst in case of catalyst poisoning or catalyst deactivation.11 The choice of the reactor also depends on the size of the reactor needed and the follows of setup and operating (does it need to be cleaned regularly or not as this costs money ad stops production).One of the biggest plants to make SNG from coal-derived syngas was started up in 1984 the Great Plains Synfuels Plant of Dakota Gasification Co. which cost $2.1billion was the only SNG plant of that scale operating in the world. The plant uses Lurgi GmbH gasifiers (a steel construction where around each time 8 tons of coal is fed into a compartment at its top, known as a coal lock, which is then sealed with a gas being fed into it ahead of the bottom of the lock opening to feed coal, in this plant the coal is brown coal which is 60-70%carbon, into the body of the gasifier, this builds up high pressure and the high pressure and temperature feed of steam and oxygen in the gasifier de compose the lignite to produce syngas). The syngas is then deepened to SNG using DPT methanation catalysts. This plant produces approximately 153 million ft3/day of SNG which is piped throughout the US. This facility has also implemented CCS (carbon capture and storage) and as of the end of last year (31/12/2009) it has captured more than 17.4 million m.t. of CO2.12As you can imagine $2.1billion is a lot of money and was worth even more in 1984 showing that using methanation to produce SNG is not a small venture but a major player in the search for more fuel as the worlds gas and oil militia are depleting. In 2009 the plant produced $264.7 million worth of SNG out of total revenue of $426.1 million. The operating costs for this plant (including maintenance) were $38,504,111.13This shows that the investment of $2.1billion was a really good decision not only in monetary value of producing SNG from methane but also a really great business return.FIGURE 3 DPTs methanation process is a refinement and further development of the Catalytic Rich Gas (CRG) process, which was first developed by British Gas Corp. in the late 1960s to convert naphtha into town gas. The process involves several methanator reactors in series, with heat recovered from the exothermic reaction (CO + 3H2 CH4 + H2O) used to raise high pressure superheated steam and to preheat the feed. severally reaction stage consists of a fixed bed of CRG catalyst operating adiabatically.12However, new and more efficient processes are being implemented in industry, that especially focus on the conversion of biomass, such as the Milena process in the Netherlands. The ECN (Energy Research Center of the Netherlands) has developed a biomass gasification technology with high gas efficiency and a high methane yield which allows it to be used for gas-engine applications. This process has been given the name Milena, and the product gas can be upgraded to SNG and ECN has the ambition to turn this into broad scale SNG production with an energy efficiency of 70%. This would be much needed as the Netherlands relies on 50% of its energy from natural gas (which is not renewable) so using SNG for biomass would be a substitute for this and the biomass is available in large quantities and it a lot cleaner and friendlier to the environment than natural gas.14The biomass has to be born-again into SNG by gasification and then methanation (theses processes and their outlines have been mentioned before). This allows it to reach efficiency, say from wood, up to 65% (this efficiency is calculated from the chemical energy output of SNG compared to the chemical energy stimulation of wood). Biomass (e.g. wood and straw) being used to produce SNG has the advantage over coal based SNG of being almost CO2 neutral, without CCS. Production of synthetic natural gas (SNG) from coal and dry biomass.4Catalyst UsedThe main catalysts that are used as methanation catalysts are nickel or nickel supported catalysts. This is because the key catalyst properties of nickel are excellent for methanation as it has long life, high activity, selectivity for the formation of methane in preference to other hydrocarbons and the low cost compared to other catalysts. One of the main disadvantages for nickel catalysts is the sensitivity to poisoning by sulphur, other catalysts are available that are sulphur-resistant and also catalyse the methanation reaction but these are much less active than nickel resulting in a slower rate of reaction.For example, one manufacturers catalysts are formulated on Ca aluminate base with the active nickel co-ordinated in a NiO/MgO solution, this leads to negligible nickel sintering.10In catalytic methanation many promoters for nickel have been studied such as copper, zinc oxide, magnesia, iron, calcium oxide, chromia and alumina. What was found was that alumina, chromia and magnesia were the best promoters in terms of activity and thermal stability. It was also found that for th ermal and mechanical stability the best of a number of NiO methanation catalysts on supports of A12O3, a mixture of A12O3 and CaO, MgO, SiO2 and Cr2 O3 was NiO-AI2O3 containing 35% NiO.15 Many other factors are taken into consideration when choosing the catalyst for the methanation process. These are explained below(i) Sulphur poisoning.Sulphur poisoning causes the methanation catalysts, to become inactive, this is because the reactants have brought in an alien molecule and this sits on the active site, the reactants now have to compete with this poison for the active sites and this results in a loss of the active surface area therefore decreasing the rate of reaction.10(ii) Thermal stability.This reaction is highly exothermic it is very important to make sure that the reaction temperature does not become too high because it affects the equilibrium state of the reaction unfavourably and the catalyst life decreases due to sintering of the metal particles, where the particles come tog ether, decreasing the surface area compared to when no sintering took place, thus less reaction is obtained. As mentioned previously the reaction temperature for this reaction is 300C-400Cfor which the nickel based catalysts used are sufficient in terms of longevity and activity. But there are catalysts tat are able to operate at higher temperatures than nickel based catalysts and these would be even more desirable as the higher the temperature at which the heat of methanation is released the more effectively can it contribute to overall thermal efficiency of the conversion process, for example of coal to SNG, it is also worthwhile to notice that at these higher temperatures the problem of sulphur poisoning decreases due to instability of the catalyst metal sulphide9. So why is it that in industry the use of catalysts that are suitable for operation at higher temperatures are not selected and for e.g. nickel catalysts are favoured? This is due to the fact that it is not eternally f easible to use the best catalyst for the process as it may cost too much to buy.(iii) Coke formation and foulingCarbon in its noble form, or as Ni3C produced on the Nickel catalyst, causes a loss of catalyst activity9. The coke formed blocks the reactants from reaching the active sites and the fouling is caused by the reaction forming a by-product which then sits on the active site, masking it. It is possible to avoid the unwanted carbon formation in the manufacture of SNG by controlling the water gas shift reaction. This is the 2nd step shown in figure 2 previously.The cost of nickel catalysts varies as the price of nickel fluctuates. The suppliers of these catalysts do not sell just a few kilograms of the catalyst they have a minimum orders quantity, e.g. 20 tons at the rate of $15000-$30000 per ton. An example of a Methanation catalyst used in industry is the SG-9701 (the name may be fancy but it is mostly nickel as shown in the table) produced by the global leader in catalysis , BASF who have found that although the catalysts operate at low temperature and show good conversion rates in the Methanation process, they eventually begin to age and lose their effectiveness, that is why through their current research they have identified that Methanation Catalyst relies on the mature combination of nickel oxide technology on an alumina matrix. However, through careful control of composition and geometry and the addition of a Rare Earth promoter, a number of performance improvements are achieved, these improvements are temperature resistance and long mechanical life. BASFs methanation catalyst also boasts a superior physical makeup reducing deterioration that can lead to increased pressure drop in the system16For the future?Another SNG project was decided upon in this April between ConocoPhillips and POSCO (a Korean steel-manufacturing company) in which ConocoPhillips E-Gas technology is being used with POSCOs Gwangyang coal to SNG project. This facility has targ eted production of 500,000 m.t. of SNG I will not go further with this project as the methanation technology to be used has not yet been announced and a new technology to produce SNG using crude oil coke (petcoke) (an advanced technology that captures and sequesters CO2 emissions from an industrial source) is to be implemented with this at a further stage. 12Hydromethanation-Peabody Energy and GreatPoint Energy Mass recently signed an agreement to produce SNG from coal, H2 from coal and also CCS projects. These are wanted to be developed with Bluegas technology, which uses catalytic Hydromethanation to produce H2 and SNG. The process is more efficient and cost effective than conventional gasification routes to SNG. In the bluegas process a propriety catalyst is dispersed with the feedstock (coal, petcoke, or biomass), and the mixture loaded into the reactor. Pressurized steam is injected from below to fluidize the mixture, which reacts to form CH4, CO2, H2 and CO.12 in that locati on is also a German-Austrian project that wants to produce methane from extra electrical energy that has been generated from solar or wind power and a process that combines methanation with electrolysis has been developed at the Center for Solar Energy and Hydrogen Research, Germany.ConclusionMethanation is a very important process especially in todays environment where we look to reduce CO2 emissions further and producing SNG from biomass using the methanation process does this rather than using natural gas. Methane is used in the gas that provides our homes with energy and heating. We need to find even more efficient processes like the ones described above that use methanation to produce SNG.